evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) general description the max98357 development board (dev board) is a fully assembled and tested pcb that evaluates the max98357 i 2 s digital input class d power amplifier. the dev board operates from a single 2.5v to 5.5v dc power supply and is capable of delivering 3.2w into a 4? load. the device outputs can be connected directly to a speaker load for filterless applications. however, a filter can be added to ease evaluation. the max98357a accepts standard i 2 s data and the max98357b accepts left-justified digital audio data. both versions also support 8-channel tdm audio data. the max98357 evaluation system (ev system) includes the max98357 dev board and maxim integrateds audio interface board (audint001 board). the audint001 board provides an easy-to-use usb audio-to-i 2 s converter. this allows for any computer to become a digital audio source, which can be used to evaluate the devices. the audint001 board can also be used to power the max98357. this allows for a complete evaluation from a single usb connection. features 2.5v to 5.5v single-supply operation only a single external component (vdd capacitor) required in many applications i 2 s, left-justified, or tdm input five selectable gains (3db, 6db, 9db, 12db, and 15db) audio channel select (left, right, and mono mix) filterless operation optional class d output filters for ease of evaluation proven pcb layout fully assembled and tested 19-6843; rev 1; 4/14 ordering information appears at end of data sheet. figure 1. simplified block diagram 10f 0.1f vdd gain 2.5v to 5.5v dac max98357 digital audio interface class d output stage outpoutn audio interface board lrclk pcm bclk din sd_mode downloaded from: http:///
maxim integrated 2 www.maximintegrated.com evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) itunes is a registered trademark of apple inc. windows media is registered trademark and registered service mark of microsoft corporation. quick start recommended equipment ? max98357 ev system ? 2.5v to 5.5v, 2a dc power supply ? usb audio source (from computer through an audio media player such as itunes ? or windows media ? player) ? 4? or 8? speaker procedure the ev system is fully assembled and tested. follow the steps below to verify board operation. caution: do not turn on the power supply until all connections are completed. 1) on the dev board verify that headers and switches are configured as follows: ju2: pins 1-3 (selects left channel) ju4: pins 1-2 (power routed from the audint001 board) j u5: pins 1-5 (12db gain) ju6: pins 2-3 (power routed from external supply) sw1: position 1-2 (part is on) 2) set the power-supply output to 5v. disable the power supply. 3) connect the power-supply ground terminal to gnd and the power-supply positive terminal to vin on the dev board. 4) with the audio source disabled, connect the usb audio source to the usb audio port (usb2) on the audint001 board. 5) connect the audint001 board to j1 on the dev board. 6) connect the speaker across the outp and outn test points. 7) enable the power-supply output. 8) enable the audio source. 9) verify that the speakers are playing the audio source signal. detailed description of hardware the max98357 ev system is designed to allow a thorough evaluation of the max98357 i 2 s digital input class d power amplifier. the dev board can be used by itself as a stand-alone evaluation board and driven directly by audio test equipment. the dev board can also be used in conjunction with the audint001 board, which allows for any computer to become an i 2 s digital audio source. the audint001 board has dc regulators that can be used to power the device. this allows for quick evalua - tion from a single usb connection. note that powering the device from the audint001 board does not allow for high-power evaluation as the input current is limited and evaluation with a speaker is not recommended. jumpers ju4 and ju6 are used to power the device from the audint001 board or external supplies connected to test points vin and vddio on the dev board. the dev board operates from a single 2.5v to 5.5v dc power supply and is capable of delivering 3.2w into a 4? load and 1.75w into an 8? load. the device outputs can be connected directly to a speaker for filterless applica - tions. however, a filter can be added to ease evaluation. the lrc components needed for evaluation of a filtered output are included with the ev kit. the max98357a accepts standard i 2 s data and the max98357b accepts left-justified digital audio data. both versions also support 8-channel tdm audio data. filterless output the dev board filterless outputs (outp, outn) can be connected directly to a speaker load without any filter - ing. use the outp and outn test points to connect the speaker directly to the device output. filtered output audio analyzers typically cannot accept the class d amplifiers pulse-width modulated (pwm) signals at their inputs. therefore, the dev board features optional low - pass filters at the outputs to ease evaluation. as shipped, the dev boards lowpass filter lrc components are unpopulated and l1, l2 are shorted on the pcb. to use the filtered output posts (foutp, foutn), remove the shorts on l1 and l2 and install components l1, l2, c3Cc9, and r5, r6. (l1 and l2 are provided separately with the dev board. components c3Cc12 and r5 and r6 are not included.) use the output posts to connect the downloaded from: http:///
maxim integrated 3 www.maximintegrated.com evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) filtered outputs to the audio analyzer. the default lowpass filters at the dev board output are optimized for a 4? speaker. jumper selection selectable gain (gain_slot) the dev board features a 5-pin jumper (ju5) to control the devices five programmable gain settings. in tdm mode, the gain is fixed at 12db and the gain pin is repurposed for slot selection. see table 1 for gain-control configuration. sd_mode input the dev board features a 4-pin jumper (ju2) to control both the audio channel that is sent to the amplifier output, along with shutdown mode. ju2 is used to select the stereo input data between the left channel, right channel, and the sum of the left/right channels. ju5 must be set to pins 1-2 and a voltage applied to the +3.3v pcb pad for proper operation. see table 2 for shunt positions. tdm mode in tdm mode, the device has a fixed gain of 12db and the gain pin becomes repurposed for slot selection. the device accepts 8-channel tdm data. the data can be either 16 bits or 32 bits wide. the gain_slot pin and sd_mode are used to select which of 8 channels of tdm data the part responds to, as shown in table 3. shutdown mode the device features a low-power shutdown mode that is activated by setting jumper sw1 to pins 2-3. to exit shut - down mode, set sw1 to pins 1-2 and select the desired stereo input channel using jumper ju2. see table 4 for switch positions. table 1. ju5 jumper selection (gain_slot) table 2. ju2 jumper selection ( sd_mode ) table 4. sw1 switch configuration table 3. tdm mode channel selection * default position. * default position. * default position. shunt position gain pin maximum gain (db) 1-2 connected to vdd through 100k? resistor r1 3 1-3 connected to vdd 6 1-4 connected to gnd through 100k? resistor r2 15 1-5* connected to gnd 12 not installed unconnected 9 shunt position sd_mode pin audio channel 1-2 connected to vddio through r3 (small resistor) right 1-3* connected to vddio through a 2k? resistor left 1-4 connected to vddio through r4 (large resistor) mono mix (left + right)/2 ju2 ju5 channel bits connected low x off n/a (1-3) (1-5) 0 16 or 32 (1-3) (1-3) 1 16 or 32 (1-3) open 2 16 or 32 (1-3) (1-2) 3 16 or 32 (1-3) (1-4) 4 16 or 32 (1-4) (1-5) 5 16 or 32 (1-4) open 6 16 or 32 (1-4) (1-3) 7 16 or 32 switch position vddio voltage device operation 1-2* vddio determined by ju4 jumper position normal (input channel selected through ju2 setting) 2-3 connected to gnd shutdown downloaded from: http:///
maxim integrated 4 www.maximintegrated.com evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) external/internal vddio (+1.8v to +3.3v) on the dev board, a logic voltage from a control interface is needed for proper selection of the stereo input channel through sd_mode . this voltage can be applied exter - nally at the vddio test point or it can be provided from circuitry on the audint001 board. see table 5 for ju4 jumper selection. logic voltages other than +3.3v can be used. if you want to use other logic voltages, resistors r3 and r4 must be adjusted. refer to the sd_mode and shutdown operation section in the max98357 ic data sheet for more information.vdd input supply (+2.5v to +5.5v) the device can accept an input supply from +2.5v to +5.5v. this voltage can be applied externally at the vdd and gnd pcb pads, or it can be provided from the audint001 board. see table 6 for ju6 jumper selection. audio interface board (audint001 board) the audint001 board provides usb-to-i 2 s data conver - sion, as well as dc regulators that can be used to power the devices. the usb-to-i 2 s converter on the audint001 board allows for any computer to become an i 2 s digital audio source. on the audint001 board, set sw1 to demo and set the i 2 s switch to connected to source audio by usb. this allows for a quick evaluation from a single usb connection. using the audint001 board as a power supply for high-power evaluation is not recom - mended as the input current is limited. for high-power evaluation, use an external supply connected to vin. driving i 2 s directly to drive i 2 s directly, apply signals at the bclk, lrclk, and sdin test points, or on the j3 header, or between j3 pins 1-2 at the appropriate locations (signal and ground are labeled on the board). evaluating the max98357b the max98357 dev board comes with a max98357a populated on the board, but can be used to evaluate the max98357b. to evaluate the max98357b, carefully remove the max98357a (u1) device from the board and replace with max98357bete+. no other component changes are required. table 5. ju4 jumper selection (vddio) table 6. ju3 jumper selection (vdd) * default position. * default position. shunt position logic voltage (vddio) 1-2* 3.3v supplied by the audint001 board connected to j1 header. 2-3 user-supplied external power supply applied at the vddio test point. shunt position input voltage (vdd) 1-2* vdd supplied from the audint001 board connected to the j1 header. 2-3 user-supplied external power supply applied at the vin pcb pad. downloaded from: http:///
maxim integrated 5 www.maximintegrated.com evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) note: indicate that you are using the max98357a/max98357b tqfn when contacting these component suppliers. designation qty description bclk, din, lrclk 3 orange multipurpose test points c1 1 10f 10%, 6.3v x5r ceramic capacitor (0603) murata grm188r60j106k c2 1 0.1f 10%, 16v x7r ceramic capacitor (0402) murata grm155r71c104k c3Cc12 0 not installed, ceramic capacitors (0402) c11 1 22pf 5%, 50v c0g ceramic capacitor (0402) murata grm1555c1h220j fb1, fb2 2 0? 5% resistors (0603) foutn, foutp, gnd, vin 4 binding posts foutn, foutp, gnd (x2), vdd 5 20g plated solid copper bus wire, 0.25in u-shaped wire loop gnd (x4), outn 5 black multipurpose test points (63 mil drill size) j1 1 26-pin (2 x 13) dual-row right- angle header, 0.1in centers j3 1 6-pin header ju2 1 4-pin header, 0.1 in centers ju4, ju6 2 3-pin headers, 0.1 in centers ju5 1 5-pin header, 0.1 in centers l1, l2 0 not installed, 22h inductors (6.2mm x 6.3mm)short (pc trace) toko d63cb series part toko a916cy-220m designation qty description outp 1 white multipurpose test point (63 mil drill size) r1, r2 2 100k? 5% resistors (0603) r3 1 226k? 1% resistor (0603) r4 1 634k? 1% resistor (0603) r5, r6 0 not installed, resistors (0402) r7Cr9 3 0? 5% resistors (0603) sw1 1 spdt jumper switch, 0.1in centers u1 1 i 2 s input class d audio ampliier (16 tqfn) maxim max98357aete+ vddio 1 red multipurpose test point (63 mil drill size) 4 shunts 1 pcb: max98357 tqfn evkit development board optional components c3Cc9 7 0.22f 10%, 6.3v x5r ceramic capacitors (0402) tdk c1005x5r0j224k c10Cc12 3 18pf 5%, 50v c0g ceramic capacitors (0402) l1, l2 2 22h, 1a inductors (6.2mm x 6.3mm) toko a916cy-220m r5, r6 2 22? 5% resistors (0402) r7Cr9 3 51? 5% resistors (0402) supplier phone website murata americas 770-436-1300 www.murataamericas.com tdk corp. 847-803-6100 www.component.tdk.com toko america, inc. 847-297-0070 www.tokoam.com component suppliers component list downloaded from: http:///
maxim integrated 6 www.maximintegrated.com evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) figure 2. max98357 dev board schematic downloaded from: http:///
maxim integrated 7 www.maximintegrated.com evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) figure 3. max98357 dev board silkscreentop figure 5. max98357 dev board pcb layoutlayer 2 figure 4. max98357 dev board pcb layoutcomponent side 1.0 1.0 1.0 downloaded from: http:///
maxim integrated 8 www.maximintegrated.com evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) # denotes rohs compliant. figure 7. max98357 dev board pcb layoutsolder side figure 6. max98357 dev board pcb layoutlayer 3 part type max98357dev#tqfn development board (dev board only) max98357evsys#tqfn evaluation system (dev + audint001 boards) 1.0 ordering information downloaded from: http:///
maxim integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim integrated product. no circuit patent licenses are implied. maxim integrated reserves the right to change the circuitry and speciications without n otice at any time. maxim integrated and the maxim integrated logo are trademarks of maxim integrated products, inc. ? 2014 maxim integrated products, inc. 9 evaluates: max98357a/max98357b (tqfn) max98357 evaluation system (tqfn) revision number revision date description pages changed 0 11/13 initial release 1 4/14 added evaluating the max98357b section, moved vddio to new pin on j1, added a 22pf capacitor to c11, and updated figures 2 and 6 4C6, 8 revision history for pricing, delivery, and ordering information, please contact maxim direct at 1-888-629-4642, or visit maxim integrateds website at www.maximintegrated.com. downloaded from: http:///
|
